How To Update Samsung S3850 Corby II Firmware Using Multiloader Program and USB Cable

Tools And Files You Need:

- Samsung S3850 Corby II Firmware Package: Download it and extract it.

- Multiloader program: Download it and extract it too.

- Samsung S3850 Corby II Original USB Drivers: After downloading the drivers you have to install it on your PC, Then restart the PC.

- USB Cable: You can use Samsung S3850 Original USB cable, Or any suitable one.

Samsung S3850 Firmware Update Steps:

- Turn off your Samsung S3850 and take out its battery, SIM Card, And MMC card too.

- Run Multiloader.exe program.

- Select BRCM2133 as CPU type.

- In case you want or need to flash Boot files too, Then check Full Download option, Otherwise leave it unchecked.

- Now you have to select the following files from the extracted firmware folder:

Click Boot button to select the complete Boot files folder.

Click Apps button to select: apps_compressed.bin

Click Rsrc1 button to select: Rsrc_S3850_xxxx_xxxxxx_Common.rc1

Click Rsrc2 button to select: Rsrc2_S3850(Low).rc2

Click Factory FS button to select: FactoryFs_S3850_xxxx_xxxxxx_Common.ffs

Click CSC button to select: CSC_S3850_xxxx_xxxxxx_Common_Oxx.csc

Click SHP APP button to select: ShpApp.app

- Put the phone's battery back but do not turn it on.

- Put your phone into Download Mode:

Press and Hold Volume Down Key + Send Key then press Power Key.

- Connect USB cable to phone and PC, Then wait until Windows detects it and install the needed drivers for it.

- Click on Search Port button, And Multiloader program will detects the phone's Com port number.

- Now you can start the update by clicking Download button.

- Multiloader program will update your phone and reboots it after that.

- Disconnect the USB cable from phone.

- When your phone is fully on, Do full reset using this code *2767*3855#

- Wait for your phone again, And after it reboots you can start using it with the new firmware version.

Important Notice: No need to flash Boot files unless you must do so, In some cases the phone will not work normally if you did not flash them, So first try to flash only Firmware files.

How To Update Samsung M8910 Pixon 12 Firmware

This model of Samsung phones comes with Touch Screen ( AMOLED resistive touchscreen, 16M colors )

and its software is so easy to deal with, so a lot of users like it so much and here we will give you the right guide to update the firmware of Samsung M8910 Pixon 12.

Tools: Samsung M8910 Pixon 12 Downloader - USB cable.

Guide: How To Update Samsung M8910 Pixon 12 Firmware.

How To Update Samsung P6200 Galaxy Tab 7.0 Plus Firmware

Update Steps:

- Extract The Downloaded Flasher,Firmwares package and USB drivers.
- Install the USB drivers and Reboot your PC.
- Run Odin Flasher and check these options: Re-Partition, Auto Reboot, F.Reset Time.
- From the Extracted Firmware Package select the files in this order:

- PIT: px_20111010_3G_16G.pit
- BOOTLOADER: P6200_APBOOT_P6200xxxxx_CL598906_REV02_user_low_ship.tar.md5
- PDA: P6200_CODE_P6200xxxxx_CL598906_REV02_user_low_ship_16G.tar.md5
- PHONE: MODEM_P6200xxxxx_REV_04_CL1083081.tar.md5
- CSC: GT-P6200-CSC-MULTI-xxxxxx.tar.md5

- At this Step you have to put the phone into Download Mode ( Volume Down + Power Key for 10 Sec ) then Press Volume Up Key to Enter Firmware Download Mode.
- Connect USB cable to Phone and PC then install needed Drivers.
- Make sure that the Odin Flasher Detects the COM number that the phone takes.
- Click Start button to update the phone with these Firmware Files.
- When all is Done in the right way the Odin Flasher will gives PASS! word In Green.
- Now you can Remove cable from phone.
- Do Full Reset by Code: *2767*3855#.

How To Update Samsung Galaxy Premier I9260 Firmware Using Odin Program And USB Cable

The Firmware Update Steps: Read the following steps first and understand them completely before starting the process.

1 - Make sure that your Galaxy Premier phone is off, Then take out its battery, SIM card, And memory card too.

2 - Double click on Odin3.exe program.

3 - At Odin's window check the following:

Re-Partition, Auto Reboot, F.Reset Time

4 - Now you will select the needed firmware files to be installed by Odin on your phone, Do it in these order:

- Click on PIT button and select GT-I9260_EUR_XX_20120711.pit
- Click on Bootloader button and select BOOTLOADER_I9260xxxxxx_...user_low_ship.tar.md5
- Click on PDA button and select PLATFORM_I9260xxxxxx_...user_low_ship.tar.md5
- Click on PHONE button and select MODEM_I9260xxxxxx_REV_00_xxx....tar.md5
- Click on CSC button and select CSC_Oxx_I9260Oxxxxxx_REV00_user_low_ship.tar.md5

5 - Odin can install the above files when your phone is into Download Mode only, To put it into that mode do these steps:

- Put its battery back, But do not turn it on.
- Press Volume Down button + HOME button + Power button until you get the warning message on your phone screen, Now release the three button and press Volume UP button only, Now you are into download mode.

6 - Using the USB cable connect your phone to the PC.

7 - Let your PC detects the new device and install any needed drivers for it, When done continue to the next step.

8 - Look at Odin's window to see if Odin detects your phone correctly, You should see 0:[COMxx] when xx is the com number of your connected phone.

9 - In case that Odin could not detect your phone, Disconnect and connect it again, Or even you can restart your PC.

10 - At this step you are ready to begin the update, All you need to do is to click on START button at Odin's window.

11 - Odin will start to install the firmware files on your Galaxy Premier, So wait until the job is done.

12 - Do not try under any condition to disconnect the USB cable or phone, And never interrupt Odin program during this process, Otherwise you may kill your phone.

13 - After the update process is done your phone will be rebooted, So wait for it.

14 - You can know if the update process is done successfully by looking at Odin's window, If you see the word PASS! then everything is ok.

15 - After your phone is on, Disconnect the USB cable from it.

16 - Do Full reset to your phone using this code: *#87976633#.

17 - Your phone will be rebooted again after entering the above code, So it is normal, Just wait for it.

18 - Now your phone is under your control with its new firmware, Customize it and enjoy your job.

Important Notices:

- The Update or Flash operation will not Sim-Unlock your device ( Unlock I9260 Galaxy Premier ).
- Use Stable PC for the update and never use USB Hub to connect the device.
- If the firmware package contains only one big file then use it in PDA field and no need to check Re.Partition option or use Pit file.

How To Flash Samsung S3030 Tobi

Tools: Samsung S3030 Download Program - USB cable.
Guide: How To Flash Samsung S3030.
Download

How To Update Firmware Of Samsung I9088 Galaxy S

Firmware Update Steps:

1. Run Samsung I9088 Galaxy S Download program.
2. Check these Options: Auto Reboot + F.Reset Time.
3. Select the PIT, PDA, PHONE & CSC file.
4. Put Device Into Download Mode ( Press Volume Down + Volume Up then connect cable ).
5. Make sure ID:COM box highlighted Yellow that the device is connected to the PC.
6. Start Downloading By pressing Start Button.
7. Wait for "Pass" to be appear on the screen.
8. After all is done reboot the phone and Do Full Reset: *2767*3855#.

How To Unlock The Bootloader of Samsung Nexus 10 - P8110

The Samsung Nexus 10 comes with locked bootloader by default, But unlocking it is possible, After you do it you will be able to access everything in its Software & Hardware without limitation, Also you should know that others can access them too, Specially your personal data, So be aware.

Keep in mind that the unlock operation will wipe all your saved data, So make a backup of everything you don't want to loose.


The needed Tools and Files:

- The original USB cable of your Samsung Nexus 10.
- Samsung Nexus 10 Fastboot Drivers: You can download it Here, Extract it to be used later.
- Fastboot Tool: Download it from Here, Extract it to C:\ to use it later.

Bootloader Unlock Steps:

1- Turn Off your Nexus 10.

2- Put your Nexus 10 into Fastboot mode: Hold Volume Up Key + Volume Down Key then press Power Key until get the Fastboot menu.

3- Connect your Nexus 10 to your PC via its USB cable, When your PC asks you for drivers browse for the extracted Fastboot Drivers folder.

4- Wait until USB drivers installed correctly.

5- From Start menu go to Command Prompt ( Black window with white input text ).

6- If you are not at C:\ then In the opened black window type CD.. and hit enter until you are in C:\

7- Now type: CD fastboot to get into fastboot folder.

8- Type this command: fastboot devices and hit enter.

9- Now you should get your connected device ID, So everything is ok till now.

10- At this step you have to type this command and hit enter: fastboot oem unlock

11- Look at your Nexus 10 screen to verify the command by selecting YES

12- Your tablet will reboot and all your data will be deleted.

13- Now your Nexus 10 Bootloader is unlocked, So you can install custom roms, Custom recovery and more.


Notice: In case you want to relock your Nexus 10 bootloader all you have to do is changing the command in step 10 to: fastboot oem lock

How To Update Firmware Of Samsung C5510

Tools: Samsung C5510 Download Program - USB cable.

Firmware: Samsung C5510 Original Firmwares

Firmware Update Steps:

1. Run Samsung C5510 Download Program.
2. Put your phone into download mode : Press Volume down + Key 9 + Power On Key.
3. Now you have to connect the USB cable to your phone.
4. Press Port Search button on the program window to check good connection with phone.
5. In case you need to flash Boot files then check Full Download option.
6. Press Boot button and show the program the Folder of the Boot files.
7. Now you have to select these files each one into his field: Amss, Rsrc1, Rsrc2, Factory FS.
8. Press Download button to start the Firmware update process.
9. Do not try to remove cable or corrupt the process or you may kill the phone.
10. After the operation finished reboot the phone and do Full reset *2767*3855#.

How To Update Samsung I9100 Galaxy S II Firmware

Firmware Update Steps:

1. Run Samsung I9100 Galaxy S II Downloader.
2. Check These options: Re-Partition , Auto Reboot , F.Reset Time.
3. Click PIT button and select: u1_02_20110310_emmc_EXT4.pit
4. Click PDA button and select: CODE_I9100xxxxx_CL161513_REV02_user_low_ship.tar.md5
5. Click PHONE button and select: MODEM_I9100xxxxx_REV_02_CL995882.tar.md5
6. Click CSC button and select: GT-I9100-MULTI-CSC-Oxxxxx.tar.md5
7. Put phone into Download mode: ( Press Volume Down + OK + Power ).
8. Connect Cable to phone and PC.
9. Make sure that the program detect the phone.
10. Click Start button and wait the program to finish downloading the firmware files to phone.
11. After phone reboot Do full reset by this Code *2767*3855#

How To Update Samsung S5660 Galaxy Gio Firmware

Firmware Update Steps:

1. Run Samsung S5660 Galaxy Gio Downloader.
2. Check these options: Auto Reboot, Protect OPS, Reset Time.
3. Click PIT button and select: Gio_v1.0.ops
4. Click BOOT button and select : APBOOT_S5660xxxxx_CL940762_REV03_user_low_true.tar.md5
5. Click PDA button and select: CODE_S5660xxxxx_CL940762_REV03_user_low_true.tar.md5
6. Click PHONE button and select: MODEM_S5660xxxxx_CL928654_REV03.tar.md5
7. Click CSC button and select: GT-S5660-MULTI-CSC-Oxxxxx.tar.md5
8. Put phone into Download mode: ( Press Volume Down + OK + Power )
9. Connect Cable to phone and PC.
10. Make sure that the program detect the phone.
11. Click Start button and wait the program to finish downloading the firmware files to phone.
12. After phone reboot Do full reset by this Code *2767*3855#

How To Update Samsung Galaxy Tab 2 10.1 SGH-T779 Firmware Version Using Odin Program

Samsung T779 Galaxy Tab 2 10.1 Firmware Update Steps:

- Turn your phone off.

- Take out its battery, SIM card, And microSD card too.

- Run Odin.exe program.

- You need to check only these two options: Auto Reboot + F.Reset Time

- Never check Re.Partition option, Unless you have Full firmware package and PIT file.

- Click on PDA button to select the single firmware update file which is located into the extracted firmware folder.

- Put the phone's battery back, But don't turn it on.

- You need to put the phone into Download Mode before connect it to PC:

Press and Hold Volume Down key then press Power key for 10 seconds, After you get the yellow triangle on screen release both keys and press Volume Up key.

- Now connect the phone to the computer using the USB cable.

- Wait until Windows detects the new device correctly and installs the drivers for it.

- When Odin detects your connected phone, You will see the COM number of it at Odin's window 0:[COMxx]

- To start the update process click on Start button at Odin's window.

- Installing the new firmware files on your Galaxy Tab 2 10.1 will take few minutes only, So wait for it to be done.

- After Odin does his job, Your phone will be rebooted.

- Unplug the USB cable from your phone.

- Look at Odin's window, If you see PASS! Word then the update was done successfully.

- When your phone is fully on, It is better to do full reset by using this code *2767*3855#

- After the phone restarts you are free to customize it as you like and start enjoying the new firmware version.

How to Update Samsung P7500 - P7501 Galaxy Tab 10.1 3G Firmware

Firmware Update:

- Run Odin Flasher and check these options: Re-Partition, Auto Reboot, F.Reset Time.
- From the Extracted Firmware package select the files like this:

PIT: android_fastboot_emmc_full_p4_16G_32G.pit
BOOTLOADER: BOOTLOADER_P7500xxxxx_CL432919.tar.md5
PDA: CODE_P7500xxxxx_CL432919_REV00_user_low_ship.tar.md5
PHONE: MODEM_P7500xxxxx_REV_00_CL1037181.tar.md5
CSC: P7500-MULTI-CSC-Oxxxxx.tar.md5

- Put the Device into Download Mode: ( Volume Down Key + Power Key for 10 sec) then Press Volume Up Key.
- Connect USB cable to PC and Phone and install Drivers.
- After Odin program detects the Phone Click Start button.
- Wait till you see PASS! word in GREEN on the Odin window.
- After the phone rebooted do Full Reset: *2767*3855#.


Important Notice: In case you found one File only inside the Firmware Package then no need to use PIT file and you can update the phone by select that file as PDA only and do the rest of steps as mentioned above.

How To Update The Firmware Of Samsung Galaxy Y Duos S6102 Using Its USB Cable and Odin Program

Firmware Update Process:

- Turn Off your phone and take its battery out.

- Run Odin3.exe program and check the following options:

Re-Partition, Auto Reboot, F.Reset Time

- Now you are going to select the firmware files from the extracted package to be installed on your phone by Odin.

- Click PIT button to select torino_1205.pit
- Click BOOTLOADER button to select BOOT_S6102xxxxx_REV02_CL1046881.tar
- Click PDA button to select PDA_S6102xxxxx_REV02_CL1046881_user_low_ship.tar
- Click PHONE button to select MODEM_S6102xxxxx_REV02_CL1046881.tar
- Click CSC button to select GT-S6102_CSC_xxxxxx....tar

- Put your phone into Download Mode so Odin can install the new firmware on it, And to do that put the phone's battery back then press the following keys:

Volume Down Key + Home Key + Power Key until you see the yellow triangle.

- Connect your phone to the PC using the USB cable.

- Wait for windows to detect the new device, And in case this is the first time you connect this phone to that PC then windows will start installing the needed drivers for it, Do nothing until windows tells you that the new device is installed and ready to use.

- Before you start the update process you should make sure that Odin program is detecting it correctly, To check that look at Odin's window and you must see 0:[COMxx] when xx is the com number of your connected phone.

- In some cases Odin program can not detect the phone, So you can try to disconnect the phone and reconnect it again, Or even restart the PC.

- Now you are ready to start and all you have to do is clicking on Start button and Odin will do it for you.

- While Odin program is installing the files on your phone, Do not stop or interrupt his work by anyway to stay away from any big problem.

- After the update process is done your phone will be rebooted, So wait for it.

- You can know if the update process is done successfully by looking at Odin's window, If you see the word PASS! then everything is ok.

- When the phone is on, Disconnect the USB cable from it.

- Do Full reset to your phone by this code: *2767*3855#.

- Your phone will be rebooted again after entering the above code, So it is normal thing just wait for it.

- Now your phone is under your control with its new firmware, Customize it and enjoy your success.

Important Notices:

- The Update or Flash operation will not Sim-Unlock your device ( Unlock S6102 Galaxy Y DUOS ).
- Use Stable PC for the update and never use USB Hub to connect the device.
- If the firmware package contains only one big file then use it in PDA field and no need to check Re.Partition option or use Pit file.

How To Update Samsung Tablets: P6800 - P6810 Galaxy Tab 7.7 Firmware

Tablet Firmware Update Steps:

- Run Odin flasher and check: Re-Partition, Auto Reboot, F.Reset Time.

- From the Extracted Firmware package's folder select the files like this:

P6800 Model:

PIT: p8_20111028_WIFI_xxG.pit

BOOTLOADER: P6800_APBOOT_P6800xxxxx_......tar.md5

PDA: P6800_CODE_P6800xxxxx_....tar.md5

PHONE: MODEM_P6800xxxxx_.....tar.md5

CSC: GT-P6800-CSC-MULTI-xxxxx.tar.md5

P6810 Model:

PIT: p8_20111028_WIFI_xxG.pit

BOOTLOADER: P6810_APBOOT_P6810xxxxx_......tar.md5

PDA: P6810_CODE_P6810xxxxx_....tar.md5

CSC: GT-P6810-CSC-MULTI-xxxxx.tar.md5

- Put your Tablet into Download Mode:

Press Volume Down Key + Power Key at the same time for about 10 seconds.
After that press Volume Up key to get into Download Mode.

- Connect USB cable to the Tablet and the PC then install the needed drivers and make sure that Odin can detect the Com port the Tablet takes ( You will see the com number in yellow at odin's window if all is ok ).

- Click on START button and wait for Odin to finish the process and reboot your tablet.

- If the update done correctly then you will see PASS! word in Green at odin's window.

- Disconnect USB cable from your tablet and do Full Reset to it by this Code: *2767*3855#.


Important Notice: For both models when you have one file inside the Firmware package then do not check Re.Partition or Use PIT file in the update, all you have to do is to select that file as PDA part then put the tablet into download mode and click Start.

How To Update Samsung S5301 Galaxy Pocket Plus Firmware Using Odin Program

Firmware Update Steps:

- Turn off your Galaxy Pocket Plus and take out its battery, SIM card, And MMC card.

- Run Odin.exe program.

- You will notice that Auto Reboot and F.Reset Time options are checked, Leave them as they are.

- In case you have or need to flash *.PIT file then check Re.Partition option, Otherwise leave it unchecked.

- In the next steps you will select the needed firmware files from the extracted firmware folder.

- Click PIT button and select the S5301 *.pit file (If you checked Re.Partition option).
- Click PDA button to select CODE_S5301xxxxxx_...REV02_...tar.md5
- Click PHONE button to select MODEM_S5301xxxxxx_...REV02_....tar.md5
- Click CSC button to select CSC_Oxx_S5301xxxxxx_...REV02_....tar.md5

- In case you have only one big file inside the firmware package, Then you need to select it as PDA file, And never check Re.Partition option or use *.pit file.

- Put the battery back into your phone, But do not turn it on.

- You should put the phone into Download Mode, Do these steps for that:

Press and Hold Volume Down key + Home key, Then press Power key.

- Connect the phone to your PC using the USB cable.

- If windows starts to install any drivers then wait until it is done.

- Odin program must detect your phone to be able to update it, So look at it and if you see 0:[COMxx] when xx are numbers then it is OK.

- Click on Start button.

- Odin will start installing the new firmware files on your Galaxy Pocket Plus.

- After Odin completes his job, Your phone will be rebooted.

- If you see the word PASS! at Odin's window then the update was done successfully.

- Disconnect the USB cable from your phone.

- When your phone is fully on it is better to do full reset by this code *2767*3855#

- You have to wait one more time for your phone to reboot, Then you can start using it with the new firmware installed.

How To Update Samsung S6312 Galaxy Young Duos Firmware - Stock Firmware

Samsung S6312 Firmware Update Steps:

- Make sure that your phone's battery has at least 90% of charging level.

- Turn your phone off.

- Take out your phone's battery, SIM Card, And memory card.

- Run Odin.exe program.

- Make sure that Auto Reboot, F.Reset Time options are checked.

- At this step you have to select the firmware files from its extracted folder:

Click PDA button to select CODE_S6312xxxxxx_900805_REV03_user_low_ship.tar.md5

Click PHONE button to select MODEM_S6312xxxxxx_900805_REV03_user_low_ship.tar.md5

Click CSC button to select CSC_Oxx_S6312Oxxxxxx_894543_REV03_user_low_ship.tar.md5

- Put your phone's battery back but don't turn it on.

- To put your phone into Download Mode:

Press and Hold Volume Down key + Home key, Then press Power key until you see the warning message on phone's screen, Now release all keys and press Volume Up key.

- Connect the USB cable to phone and PC.

- Wait for windows for detecting it, And installing any needed drivers.

- When Odin program correctly detects the phone, You will see 0:[COMxx] when xx are numbers.

- To begin the update click on Start button.

- Your phone will be rebooted by Odin program after installing the new firmware files into your phone, And you can see PASS! Word at Odin program.

- Now it is safe to disconnect the USB cable from phone.

- Wait until the phone is fully on, And then do a full reset using this code *2767*3855#

- Once again you should wait for your phone to restart.

- Now your Samsung Galaxy Young Duos is updated and you can enjoy using the new firmware version.


Notice: If the Firmware Package contains only one big file, Then you have to select it as PDA file, And follow all the other steps as they are.

How To Update Samsung I9103 Galaxy R Firmware

Firmware Update Guide:

- Run Samsung I9103 Galaxy R Downloader.

- Check these options: Auto Reboot / F.Reset Time.

- Now in case you have only one file in the Firmware package then it is PDA part.

- In case you have three files in the Firmware package then select like this:

PDA part: CODE_I9103xxxxx_CL423654_REV00_user_low_ship.tar.md5

PHONE part: MODEM_I9103xxxxx.tar

CSC part: GT-I9103-MULTI-CSC-Oxxxxx.tar.md5

- Put the phone into download mode: Volume Down + Home + Power.

- Press Volume Up key to enter Download Mode.

- Connect USB cable to Phone and PC.

- After the Downloader detect the phone click Start button.

- Do nothing till all is done and the phone restart.

- Make Full Reset by Code *2767*3855#.

How To Update Samsung Galaxy Chat B5330 Firmware Using Odin and Original Firmware Package

Tools and Drivers:

- Samsung Galaxy Galaxy Chat GT-B5330 Firmware Package:
Select and Download the wanted Firmware package for your phone and extract it.

- Odin original flasher: B5330 Galaxy Chat and extract it.
- USB Drivers: Download and install this drivers to let your PC recognize the device when connected and it is better to restart your PC after installing the drivers.


Firmware Update Steps:

- Turn your phone off and remove Sim and Memory Card from it.

- Run Odin program and check the following options:

Auto Reboot - Re-Partition - F.Reset Time

- Click on PIT button and select: Zanin.pit

- From the Extracted Firmware package you have to select files in the following order to use them in Odin program:

Bootloader: BOOT_B5330xxxxxx_REV05.tar

PDA: CODE_B5330xxxxxx_20120603.122112_REV05_user_high_noship.tar

PHONE: MODEM_B5330xxxxxx_REV05.tar

CSC: CSC_Oxx_B5330Oxxxxxx_20120603.122112_REV05_user_high_noship.tar

- Now put the phone into Download Mode: Press Volume Down key + OK Key + Power Key.

- After you see the Warning message press Volume Up Key to enter Download Mode.

- Connect the phone to your PC via USB cable.

- If your PC starts installing drivers then wait till it is finished.

- Look at Odin's window and make sure it detects the Com port that your phone takes:

If the phone's drivers is installed correctly you will see 0:[COMxx] when xx is the com port number so everything is OK.

- Click Start button to let Odin downloads the selected firmware files into your phone.

- during the update process it is very risky to stop the program or remove USB cable from phone so let it done without any interruption.

- When the update process is done the phone will be rebooted.

- If you see PASS! word at Odin's window then the update was successful.

- Disconnect your phone and wait till it is fully on.

- It is better to do Full Reset by this Code: *#87976633# and let the phone rebooted.

- After it is on again you can use the setup wizard to select your favorite settings and enjoying your updated phone.


Important Notices:

- The Update or Flash operation will not Sim-Unlock your device ( Unlock B5330 Galaxy Chat ).
- Use Stable PC for the update and never use USB Hub to connect the device.
- Fully charge your device's battery before updating it.
- Keep in mind to backup any wanted data from your device before the update.
- If the firmware package contains only one big file then use it in PDA field and no need to check Re.Partition option or use Pit file.

How To Update Samsung P7510 Galaxy Tab 10.1 WiFi Firmware

Firmware Update Steps:

1. Run Samsung P7510 Downloader.
2. Check these options: Re-Partition, Auto Reboot, F.Reset Time.
3. Click PIT button and select: android_fastboot_emmc_full_p4_16G_32G.pit
4. Put the Tablet into dwonload mode: ( Press Volume Down + Power for 10 sec ) then press Volume Up to enter Dwonload mode.
5. Connect USB cable to phone and PC.
6. Make sure that the program has detect the phone.
7. Click Start button to flash PIT file and wait to see PASS! word on the program.
8. Now click on Reset button and uncheck this option: Re-Partition.
9. Click BOOTLOADER button and select: BOOTLOADER_P7510xxxxx_CL317542.tar.md5
10. Click PDA button and select: CODE_P7510xxxxx_CL317542_REV00_user_low_ship.tar.md5
11. Click CSC button and select: CSC_P7510Oxxxxx.tar.md5
12. Remove battery off and reinsert it then put the phone into download mode again.
13. Connect USB cable to phone and PC.
14. Make sure that the program has detect the phone.
15. Click Start button to and wait to see PASS! word on the program.
16. After phone rebooted do full reset by this code: *2767*3855#

How To Update Samsung Galaxy Note 10.1 N8000 and N8010 Firmwares by Odin Program

Firmware Update Steps:

- Extract Firmware package and Odin flasher to a known place on your PC hard disk.

- Double click on Odin.exe to run the program.

- Check these options at Odin's window: Re-Partition, Auto Reboot, and F.Reset Time.

- At this step you have to select the Firmware files each one in his suitable place:

PIT: GT-N8xxx_note10.1.pit
PDA: CODE_N8000xxxxxx_....tar
PHONE: MODEM_N8000xxxxxx_....tar
CSC: CSC_Oxx_N8000xxxxxx_....tar

- In case your device is N8010 then there is no need to select anything in PHONE field as this model does not support GSM.

- Turn Off the device wait for some seconds then put it into download mode.

- Press Volume Down key + Power Key for 10 Seconds.

- After you get a warning message on your device LCD press Volume Up key to get into Download Mode.

- Use the Original USB cable of the device to connect it to your PC ( never use any USB HUB ).

- If this is the First time you connect the device to this PC the USB drivers will be installed so wait till that is done.

- When Odin flasher detects your device correctly you will see 0:[COMxxx] in yellow.

- At this point you are ready to start the Update process so click START button and Odin will do his job.

- During the process it is very important to not interrupt it at all to stay away from any possible problems.

- After Odin updates your device it will rebooted automatically so wait for it.

- When it is fully on then disconnect the USB cable from it.

- It is better to do Full Reset by code: *#87976633#

- The above code will reset the device and reboots it again.

- Now it is your role to setup your device the way you want and like.


Important Notices:

- The Update or Flash operation will not Sim-Unlock your device ( Unlock N8000 ).
- Use Stable PC for the update and never use USB Hub to connect the device.
- Fully charge your device's battery before updating it.
- Keep in mind to backup any wanted data from your device before the update.
- If the firmware package contains only one big file then use it in PDA field and no need to check Re.Partition option or use Pit file.

How To Update Samsung I9105P Galaxy S2 Plus Firmware Using Odin Flasher

Samsung Galaxy S II Plus Firmware Update Steps:

- Turn off your phone and take its battery out.

- Double click on Odin3.exe program to run it.

- Check these options:

• Re-Partition ( No need to check this option, Unless you want to flash *.pit file. So you can install the firmware without it too. Use it to repartition your phone only).
• Auto Reboot
• F.Reset Time

- In the following step you will select the firmware files from the package you already downloaded.

- Click on PIT button and select: s2vip.pit

- Click on Bootloader button and select: DefaultCalDataWithBoot_I9105Pxxxxxx..tar.md5

- Click on PDA button and select: CODE_I9105Pxxxxxx...tar.md5

- Click on PHONE button and select: MODEM_I9105Pxxxxxx...tar.md5

- Click on CSC button and select: CSC_Oxx_I9105POxxxxxx...tar.md5

- Your phone must be into Download Mode:

Hold Volume Down Key + Home Key then press Power Key until you see the warning message on phone's screen, Then press Volume UP Key to enter the Download Mode.

- Use the USB cable to connect your Phone to PC.

- Wait until your PC detects the phone correctly, And installs the needed drivers for it.

- Look at Odin's window, You should see the COM number of your phone like this 0:[COMxx] when xx are numbers.

- In case Odin could not detect the phone, You may need to restart your PC and try again.

- After you make sure that Odin detects your phone, All you have to do is hitting START button.

- Odin will start to install the firmware files on your phone, Wait until your phone being rebooted by Odin.

- When your phone rebooted, Look at at Odin's window to check if the update was done successfully, You should see PASS! Word.

- After your phone is completely on, Do full reset using this code *#87976633#

- You have to wait one more time until the phone reboots, Then you can customize it the way you like to use.

Notices:

- Flashing or Updating your phone will not remove any SIM locks, If you want to unlock your Samsung Galaxy S2 Plus I9105P Check our Online Unlock Service.

- When you have only one file inside the firmware package, No need to check Re-Partition option or using *.pit file, And select the file as PDA only.

How To Update Samsung C3752 Duos Firmware Version Using USB Cable

Samsung C3752 Duos Firmware Update Steps:

- Turn your Samsung C3752 off, And take its battery, SIM cards, And MMC card out.

- From the flasher folder run FlashTool_E2.exe

- To Select the Firmware files from its extracted folder click on (...) button,You have to do so  for each file.

- The selecting of firmware files must be in the below order:

- C3752xxxxx_psi.fls
- C3752xxxxx_slb.fls
- C3752xxxxx_BSY.fls
- C3752xxxxx_CDS.fls
- C3752Oxxxxx_CSC.dffs (Or C3752Oxxxxx_dffs.dffs in some versions)

- Now Check these settings:

Custom Order (Must be checked).
Erases Calibration! : Select (Erase whole flash before download).
Baud Rate: 921600
Communication Driver: Infineon USB Driver.

- Now you can click on Next button, And a new window will appear.

- Click on Start USB1 button.

- Now you have to connect your Samsung C3752 to PC using the USB cable.

- There are more than one way to connect your phone, You can try any one of the following:

1- With the phone's battery in, Press (*) key then connect the USB cable to it.

2- Connect the USB cable to phone without battery, After it is detected you can insert the battery.

- After the FlashTool starts the update process you have to wait for some minutes.

- When the operation is done, You will see a Success word, And that means it was done right.

- Disconnect the USB cable from phone.

- With your Samsung C3752 Duos on, Do a full reset by this code *2767*3855#

- Now when your phone restart it will be ready for using with its new firmware.

How To Update Firmware Of Samsung N7000 Galaxy Note

Firmware Update Guide:

- Run Samsung N7000 Galaxy Note Downloader.

- Check these options: Re-Partition, Auto Reboot, and F. Reset Time.

- Now you have to select Pit file and Firmware files too like this:

PIT: Q1_20110914_16GB.pit

PDA: CODE_N7000xxxxx_CL627135_REV02_user_low_ship.tar.md5

PHONE: MODEM_N7000xxxxx_REV_05_CL1067428.tar.md5

CSC: GT-N7000-MULTI-CSC-Oxxxxx.tar.md5

- Put phone into Download Mode: press Volume Down + Home + Power, then press Volume Up.

- Connect USB cable to phone and make sure the program detect it.

- Click Strat button and wait till the program finishes the process.

- After the phone restarted disconnect USB cable.

- Do Full Reset by Code: *2767*3855#