How To Update Samsung Tablets: P6800 - P6810 Galaxy Tab 7.7 Firmware

Tablet Firmware Update Steps:

- Run Odin flasher and check: Re-Partition, Auto Reboot, F.Reset Time.

- From the Extracted Firmware package's folder select the files like this:

P6800 Model:

PIT: p8_20111028_WIFI_xxG.pit

BOOTLOADER: P6800_APBOOT_P6800xxxxx_......tar.md5

PDA: P6800_CODE_P6800xxxxx_....tar.md5

PHONE: MODEM_P6800xxxxx_.....tar.md5

CSC: GT-P6800-CSC-MULTI-xxxxx.tar.md5

P6810 Model:

PIT: p8_20111028_WIFI_xxG.pit

BOOTLOADER: P6810_APBOOT_P6810xxxxx_......tar.md5

PDA: P6810_CODE_P6810xxxxx_....tar.md5

CSC: GT-P6810-CSC-MULTI-xxxxx.tar.md5

- Put your Tablet into Download Mode:

Press Volume Down Key + Power Key at the same time for about 10 seconds.
After that press Volume Up key to get into Download Mode.

- Connect USB cable to the Tablet and the PC then install the needed drivers and make sure that Odin can detect the Com port the Tablet takes ( You will see the com number in yellow at odin's window if all is ok ).

- Click on START button and wait for Odin to finish the process and reboot your tablet.

- If the update done correctly then you will see PASS! word in Green at odin's window.

- Disconnect USB cable from your tablet and do Full Reset to it by this Code: *2767*3855#.


Important Notice: For both models when you have one file inside the Firmware package then do not check Re.Partition or Use PIT file in the update, all you have to do is to select that file as PDA part then put the tablet into download mode and click Start.

How To Update Samsung S5301 Galaxy Pocket Plus Firmware Using Odin Program

Firmware Update Steps:

- Turn off your Galaxy Pocket Plus and take out its battery, SIM card, And MMC card.

- Run Odin.exe program.

- You will notice that Auto Reboot and F.Reset Time options are checked, Leave them as they are.

- In case you have or need to flash *.PIT file then check Re.Partition option, Otherwise leave it unchecked.

- In the next steps you will select the needed firmware files from the extracted firmware folder.

- Click PIT button and select the S5301 *.pit file (If you checked Re.Partition option).
- Click PDA button to select CODE_S5301xxxxxx_...REV02_...tar.md5
- Click PHONE button to select MODEM_S5301xxxxxx_...REV02_....tar.md5
- Click CSC button to select CSC_Oxx_S5301xxxxxx_...REV02_....tar.md5

- In case you have only one big file inside the firmware package, Then you need to select it as PDA file, And never check Re.Partition option or use *.pit file.

- Put the battery back into your phone, But do not turn it on.

- You should put the phone into Download Mode, Do these steps for that:

Press and Hold Volume Down key + Home key, Then press Power key.

- Connect the phone to your PC using the USB cable.

- If windows starts to install any drivers then wait until it is done.

- Odin program must detect your phone to be able to update it, So look at it and if you see 0:[COMxx] when xx are numbers then it is OK.

- Click on Start button.

- Odin will start installing the new firmware files on your Galaxy Pocket Plus.

- After Odin completes his job, Your phone will be rebooted.

- If you see the word PASS! at Odin's window then the update was done successfully.

- Disconnect the USB cable from your phone.

- When your phone is fully on it is better to do full reset by this code *2767*3855#

- You have to wait one more time for your phone to reboot, Then you can start using it with the new firmware installed.

How To Update Samsung S6312 Galaxy Young Duos Firmware - Stock Firmware

Samsung S6312 Firmware Update Steps:

- Make sure that your phone's battery has at least 90% of charging level.

- Turn your phone off.

- Take out your phone's battery, SIM Card, And memory card.

- Run Odin.exe program.

- Make sure that Auto Reboot, F.Reset Time options are checked.

- At this step you have to select the firmware files from its extracted folder:

Click PDA button to select CODE_S6312xxxxxx_900805_REV03_user_low_ship.tar.md5

Click PHONE button to select MODEM_S6312xxxxxx_900805_REV03_user_low_ship.tar.md5

Click CSC button to select CSC_Oxx_S6312Oxxxxxx_894543_REV03_user_low_ship.tar.md5

- Put your phone's battery back but don't turn it on.

- To put your phone into Download Mode:

Press and Hold Volume Down key + Home key, Then press Power key until you see the warning message on phone's screen, Now release all keys and press Volume Up key.

- Connect the USB cable to phone and PC.

- Wait for windows for detecting it, And installing any needed drivers.

- When Odin program correctly detects the phone, You will see 0:[COMxx] when xx are numbers.

- To begin the update click on Start button.

- Your phone will be rebooted by Odin program after installing the new firmware files into your phone, And you can see PASS! Word at Odin program.

- Now it is safe to disconnect the USB cable from phone.

- Wait until the phone is fully on, And then do a full reset using this code *2767*3855#

- Once again you should wait for your phone to restart.

- Now your Samsung Galaxy Young Duos is updated and you can enjoy using the new firmware version.


Notice: If the Firmware Package contains only one big file, Then you have to select it as PDA file, And follow all the other steps as they are.

How To Update Samsung I9103 Galaxy R Firmware

Firmware Update Guide:

- Run Samsung I9103 Galaxy R Downloader.

- Check these options: Auto Reboot / F.Reset Time.

- Now in case you have only one file in the Firmware package then it is PDA part.

- In case you have three files in the Firmware package then select like this:

PDA part: CODE_I9103xxxxx_CL423654_REV00_user_low_ship.tar.md5

PHONE part: MODEM_I9103xxxxx.tar

CSC part: GT-I9103-MULTI-CSC-Oxxxxx.tar.md5

- Put the phone into download mode: Volume Down + Home + Power.

- Press Volume Up key to enter Download Mode.

- Connect USB cable to Phone and PC.

- After the Downloader detect the phone click Start button.

- Do nothing till all is done and the phone restart.

- Make Full Reset by Code *2767*3855#.

How To Update Samsung Galaxy Chat B5330 Firmware Using Odin and Original Firmware Package

Tools and Drivers:

- Samsung Galaxy Galaxy Chat GT-B5330 Firmware Package:
Select and Download the wanted Firmware package for your phone and extract it.

- Odin original flasher: B5330 Galaxy Chat and extract it.
- USB Drivers: Download and install this drivers to let your PC recognize the device when connected and it is better to restart your PC after installing the drivers.


Firmware Update Steps:

- Turn your phone off and remove Sim and Memory Card from it.

- Run Odin program and check the following options:

Auto Reboot - Re-Partition - F.Reset Time

- Click on PIT button and select: Zanin.pit

- From the Extracted Firmware package you have to select files in the following order to use them in Odin program:

Bootloader: BOOT_B5330xxxxxx_REV05.tar

PDA: CODE_B5330xxxxxx_20120603.122112_REV05_user_high_noship.tar

PHONE: MODEM_B5330xxxxxx_REV05.tar

CSC: CSC_Oxx_B5330Oxxxxxx_20120603.122112_REV05_user_high_noship.tar

- Now put the phone into Download Mode: Press Volume Down key + OK Key + Power Key.

- After you see the Warning message press Volume Up Key to enter Download Mode.

- Connect the phone to your PC via USB cable.

- If your PC starts installing drivers then wait till it is finished.

- Look at Odin's window and make sure it detects the Com port that your phone takes:

If the phone's drivers is installed correctly you will see 0:[COMxx] when xx is the com port number so everything is OK.

- Click Start button to let Odin downloads the selected firmware files into your phone.

- during the update process it is very risky to stop the program or remove USB cable from phone so let it done without any interruption.

- When the update process is done the phone will be rebooted.

- If you see PASS! word at Odin's window then the update was successful.

- Disconnect your phone and wait till it is fully on.

- It is better to do Full Reset by this Code: *#87976633# and let the phone rebooted.

- After it is on again you can use the setup wizard to select your favorite settings and enjoying your updated phone.


Important Notices:

- The Update or Flash operation will not Sim-Unlock your device ( Unlock B5330 Galaxy Chat ).
- Use Stable PC for the update and never use USB Hub to connect the device.
- Fully charge your device's battery before updating it.
- Keep in mind to backup any wanted data from your device before the update.
- If the firmware package contains only one big file then use it in PDA field and no need to check Re.Partition option or use Pit file.

How To Update Samsung P7510 Galaxy Tab 10.1 WiFi Firmware

Firmware Update Steps:

1. Run Samsung P7510 Downloader.
2. Check these options: Re-Partition, Auto Reboot, F.Reset Time.
3. Click PIT button and select: android_fastboot_emmc_full_p4_16G_32G.pit
4. Put the Tablet into dwonload mode: ( Press Volume Down + Power for 10 sec ) then press Volume Up to enter Dwonload mode.
5. Connect USB cable to phone and PC.
6. Make sure that the program has detect the phone.
7. Click Start button to flash PIT file and wait to see PASS! word on the program.
8. Now click on Reset button and uncheck this option: Re-Partition.
9. Click BOOTLOADER button and select: BOOTLOADER_P7510xxxxx_CL317542.tar.md5
10. Click PDA button and select: CODE_P7510xxxxx_CL317542_REV00_user_low_ship.tar.md5
11. Click CSC button and select: CSC_P7510Oxxxxx.tar.md5
12. Remove battery off and reinsert it then put the phone into download mode again.
13. Connect USB cable to phone and PC.
14. Make sure that the program has detect the phone.
15. Click Start button to and wait to see PASS! word on the program.
16. After phone rebooted do full reset by this code: *2767*3855#

How To Update Samsung Galaxy Note 10.1 N8000 and N8010 Firmwares by Odin Program

Firmware Update Steps:

- Extract Firmware package and Odin flasher to a known place on your PC hard disk.

- Double click on Odin.exe to run the program.

- Check these options at Odin's window: Re-Partition, Auto Reboot, and F.Reset Time.

- At this step you have to select the Firmware files each one in his suitable place:

PIT: GT-N8xxx_note10.1.pit
PDA: CODE_N8000xxxxxx_....tar
PHONE: MODEM_N8000xxxxxx_....tar
CSC: CSC_Oxx_N8000xxxxxx_....tar

- In case your device is N8010 then there is no need to select anything in PHONE field as this model does not support GSM.

- Turn Off the device wait for some seconds then put it into download mode.

- Press Volume Down key + Power Key for 10 Seconds.

- After you get a warning message on your device LCD press Volume Up key to get into Download Mode.

- Use the Original USB cable of the device to connect it to your PC ( never use any USB HUB ).

- If this is the First time you connect the device to this PC the USB drivers will be installed so wait till that is done.

- When Odin flasher detects your device correctly you will see 0:[COMxxx] in yellow.

- At this point you are ready to start the Update process so click START button and Odin will do his job.

- During the process it is very important to not interrupt it at all to stay away from any possible problems.

- After Odin updates your device it will rebooted automatically so wait for it.

- When it is fully on then disconnect the USB cable from it.

- It is better to do Full Reset by code: *#87976633#

- The above code will reset the device and reboots it again.

- Now it is your role to setup your device the way you want and like.


Important Notices:

- The Update or Flash operation will not Sim-Unlock your device ( Unlock N8000 ).
- Use Stable PC for the update and never use USB Hub to connect the device.
- Fully charge your device's battery before updating it.
- Keep in mind to backup any wanted data from your device before the update.
- If the firmware package contains only one big file then use it in PDA field and no need to check Re.Partition option or use Pit file.

How To Update Samsung I9105P Galaxy S2 Plus Firmware Using Odin Flasher

Samsung Galaxy S II Plus Firmware Update Steps:

- Turn off your phone and take its battery out.

- Double click on Odin3.exe program to run it.

- Check these options:

• Re-Partition ( No need to check this option, Unless you want to flash *.pit file. So you can install the firmware without it too. Use it to repartition your phone only).
• Auto Reboot
• F.Reset Time

- In the following step you will select the firmware files from the package you already downloaded.

- Click on PIT button and select: s2vip.pit

- Click on Bootloader button and select: DefaultCalDataWithBoot_I9105Pxxxxxx..tar.md5

- Click on PDA button and select: CODE_I9105Pxxxxxx...tar.md5

- Click on PHONE button and select: MODEM_I9105Pxxxxxx...tar.md5

- Click on CSC button and select: CSC_Oxx_I9105POxxxxxx...tar.md5

- Your phone must be into Download Mode:

Hold Volume Down Key + Home Key then press Power Key until you see the warning message on phone's screen, Then press Volume UP Key to enter the Download Mode.

- Use the USB cable to connect your Phone to PC.

- Wait until your PC detects the phone correctly, And installs the needed drivers for it.

- Look at Odin's window, You should see the COM number of your phone like this 0:[COMxx] when xx are numbers.

- In case Odin could not detect the phone, You may need to restart your PC and try again.

- After you make sure that Odin detects your phone, All you have to do is hitting START button.

- Odin will start to install the firmware files on your phone, Wait until your phone being rebooted by Odin.

- When your phone rebooted, Look at at Odin's window to check if the update was done successfully, You should see PASS! Word.

- After your phone is completely on, Do full reset using this code *#87976633#

- You have to wait one more time until the phone reboots, Then you can customize it the way you like to use.

Notices:

- Flashing or Updating your phone will not remove any SIM locks, If you want to unlock your Samsung Galaxy S2 Plus I9105P Check our Online Unlock Service.

- When you have only one file inside the firmware package, No need to check Re-Partition option or using *.pit file, And select the file as PDA only.

How To Update Samsung C3752 Duos Firmware Version Using USB Cable

Samsung C3752 Duos Firmware Update Steps:

- Turn your Samsung C3752 off, And take its battery, SIM cards, And MMC card out.

- From the flasher folder run FlashTool_E2.exe

- To Select the Firmware files from its extracted folder click on (...) button,You have to do so  for each file.

- The selecting of firmware files must be in the below order:

- C3752xxxxx_psi.fls
- C3752xxxxx_slb.fls
- C3752xxxxx_BSY.fls
- C3752xxxxx_CDS.fls
- C3752Oxxxxx_CSC.dffs (Or C3752Oxxxxx_dffs.dffs in some versions)

- Now Check these settings:

Custom Order (Must be checked).
Erases Calibration! : Select (Erase whole flash before download).
Baud Rate: 921600
Communication Driver: Infineon USB Driver.

- Now you can click on Next button, And a new window will appear.

- Click on Start USB1 button.

- Now you have to connect your Samsung C3752 to PC using the USB cable.

- There are more than one way to connect your phone, You can try any one of the following:

1- With the phone's battery in, Press (*) key then connect the USB cable to it.

2- Connect the USB cable to phone without battery, After it is detected you can insert the battery.

- After the FlashTool starts the update process you have to wait for some minutes.

- When the operation is done, You will see a Success word, And that means it was done right.

- Disconnect the USB cable from phone.

- With your Samsung C3752 Duos on, Do a full reset by this code *2767*3855#

- Now when your phone restart it will be ready for using with its new firmware.

How To Update Firmware Of Samsung N7000 Galaxy Note

Firmware Update Guide:

- Run Samsung N7000 Galaxy Note Downloader.

- Check these options: Re-Partition, Auto Reboot, and F. Reset Time.

- Now you have to select Pit file and Firmware files too like this:

PIT: Q1_20110914_16GB.pit

PDA: CODE_N7000xxxxx_CL627135_REV02_user_low_ship.tar.md5

PHONE: MODEM_N7000xxxxx_REV_05_CL1067428.tar.md5

CSC: GT-N7000-MULTI-CSC-Oxxxxx.tar.md5

- Put phone into Download Mode: press Volume Down + Home + Power, then press Volume Up.

- Connect USB cable to phone and make sure the program detect it.

- Click Strat button and wait till the program finishes the process.

- After the phone restarted disconnect USB cable.

- Do Full Reset by Code: *2767*3855#

How To Update Firmware Of Samsung S5330 Wave 2 Pro

Firmware Update Steps:

1. Put you phone into Download Mode ( Press Volume DOWN + Camera key and Power Button ).
2. Run Samsung S5330 Wave 2 Pro Downloader.
3. Select BRCM2133
4. In case You want to change Phone Boot too the check Full Download option.
5. Press Boot button and select Boot files folder.
6. Now you have too select these files each one in his field: Apps, Rsrc1, Rsec2, Factory FS, ShpApp, Fota.
7. Press on Port Search button to check good connection with phone.
8. Click on Download button to start updating your phone.
9. Do Not touch or remove cable from the phone till the operation finished.
10. After it done the phone will restart by itself.
11. Do Full reset: *2767*3855# and it is Done.

How To Update Samsung C3050 / C3053 Stratus Firmware

Tools: Samsung C3050 Stratus Downloader - Original USB cable.

Firmwares: Samsung C3050 / C3053 Stratus Original Firmwares

Flashing Steps:

1. Run Samsung C3050 Stratus Downloader.
2. Select: "Options" > "Settings" >"Generic" >"Specify hardware platform".
3. Select Customer T: Stratus (Intel Sibley 512/128, USB).
4. Also check this Option: Erase all Unused Regions.
5. Connect the phone in Download mode:( Press * + END call ) and connect USB cable to phone.
6. Now select the Com Port that the phone takes.
7. From Flash and Verify tab select S3 flash file you want to flash it.
8. From Default Contents tab select CSC file and check: S-record with Contents.
9. Click on Flash button and type YES in the message box then click OK to Start the process.
10. Do not touch or remove the cable till the Program tell you: All is Well.
11. Turn On the phone and do full reset by the code: *2767*3855#.

How To Update Firmware Of Samsung I5800 Galaxy 3

Firmware Update Steps:

1. Run Samsung I5800 Galaxy 3 Downloader.
2. Click OPS button and select: apollo_0531.ops
3. Click BOOT button and select: I5800xxxxx-REV02-Bootloader-low-CL794643.tar.md5
4. Click PHONE button and select: I5800xxxxx_PHONE.tar.md5
5. Click PDA button and select: I5800xxxxx-REV02-PDA-CL794643.tar.md5
6. Click CSC button and select: I5800Oxxxxx-CSC-MULTI-OXX.tar.md5
7. Check these options: Auto Reboot, Protect OPS, Reset Time
8. Put the phone into download mode: Press Volume Down Key + OK Key + Power Key
9. Connect USB cable to phone and PC.
10. Make sure the program detect the COM the phone takes.
11. Press Start button and wait till all is done.
12. Turn On the phone and do full reset by this Code: *2767*3855#.

How To Update Samsung S5570 Galaxy Mini Firmware

Firmware Update Steps:

1. Run Samsung S5570 Galaxy Mini Downloader.
2. Select OPS file: TASS_v1.0.ops
3. Click BOOT button and select: APBOOT_S5570xxxxx_xxx..._user_mid_false.tar.md5
4. Click Phone button and select: MODEM_S5570xxxxx_xxx...._REV02.tar.md5
5. Click PDA button and select: CODE_S5570xxxxx_xxx..._REV02_user_mid_false.tar.md5
6. Click CSC button and select: CSC_S5570xxxxxx_xxx..._REV02_user_mid_false.tar.md5
7. Put your phone into Download Mode: Press middle Key ( Home key ) + Power + Volume Down
8. Connect USB cable to your phone and the program must read the Com number it takes.
9. Click Start button and the update process will start.
10. Do not touch or remove anything till the device rebooted and you can see PASS word on the program.

How To Update Firmware Of Samsung I9010 Galaxy S Giorgio Armani

Firmware Update Steps:

1. Run Samsung I9010 Galaxy S Giorgio Armani Downloader.
2. Check Re-Partition and Phone Bootloader Update options.
3. Select the PIT, PDA, PHONE & CSC files each one in his field.
4. Enter Device into Download Mode: Press Volume Down + Power And connect Cable.
5. Make sure ID:COM box highlighted yellow to know that the handset is connected to the PC.
6. Start Downloading by clicking Start Button.
7. Handset reboots when download completes.
8. Do Full Reset : *2767*3855#.

Samsung I9010 Galaxy S Giorgio Armani Original Firmwares.

How To Update The Firmware Version Of Samsung S6810 Galaxy Fame, And S6810P Galaxy Fame NFC

Files and Programs:

- Original Firmware Package for Samsung S6810 / S6810P.
- Odin Flasher.
- USB Drivers for Samsung Galaxy Fame.

Tools:

- Original USB cable for Samsung Galaxy Fame, Or any suitable one.
- A computer running Windows OS.

Samsung Galaxy Fame Firmware Update Steps:

- After downloading the needed files and programs, Extract any zipped one, And install the USB drivers, Then it is better to restart your computer.

- Check your phone's battery (Must be at least at 90%).

- Turn Off the phone.

- Take out the phone's battery, SIM card, And memory card too.

- Run Odin.exe flasher program.

- Auto Reboot, F.Reset Time options must be checked.

- In case you need to flash *.PIT file too, Then check Re-Partition option.

- Click on PIT button and select: nevisp.pit file (only when Re-Partition is checked).

- Now you are going to select the firmware files from its extracted folder:

Click Bootloader button to select: BOOT_S6810xxxxxx_REV00.tar.md5

Click PDA button to select: CODE_S6810xxxxxx_xxxx_REV00_...tar.md5

Click PHONE button to select: MODEM_S6810xxxxxx_REV00.tar.md5

Click CSC button to select: CSC_Oxx_S6810xxxxxx_xxxx_REV00_...tar.md5

- Put the phone's battery back, But do not turn it on.

- To put the Galaxy Fame into Download Mode you have to:

Press and Hold Volume Down key + Home key, Then press Power key.

- Connect it to the computer via the USB cable, And wait for it to be detected.

- Odin will detect the Com number of your phone, It will look like this 0:[COMxx].

- Click on Start button.

- Odin program will start installing the selected firmware files into your Galaxy Fame.

- You have to wait for some minutes, But don't interrupt the process at all.

- Your phone will be rebooted after the process is done.

- If it was a successful update, You will see PASS! word at Odine's window.

- Disconnect the USB cable from phone.

- When your phone is fully on, You can do a full reset by this code *2767*3855#

Notices:
- When you have one file inside the firmware update package, Then don't check Re-Partition option, And don't select any PIT file. The one file must be selected as PDA file.

How To Update Samsung E900 Firmware

In this Guide you can get the right steps for Flashing Samsung E900.

Tools: Samsung E900 Download Program - USB cable.

Firmwares: Samsung E900 Original Firmwares

Firmware Update Steps:

1. Run Samsung E900 Download Program.
2. Select: "Options" > "Settings" >"Generic" >"Specify hardware platform".
3. Select Customer T: D830/D840/E900 ( USB ).
4. Also check this Option: Erase all Unused Regions.
5. Connect the phone in Download mode:( Press * + END call ) and connect USB cable to phone.
6. Now select the Com Port that the phone takes.
7. From Flash and Verify tab select S3 flash file you want to flash it.
8. From Default Contents tab select CTS file and check: S-record with Contents.
9. Click on Flash button and type YES in the message box then click OK to Start the process.
10. Do not touch or remove the cable till the Program tell you: All is Well.
11. Turn On the phone and do full reset by the code: *2767*3855#.

How To Update Samsung P3100 Galaxy Tab 2 7.0 Firmware

Tools:
- Samsung P3100 Galaxy Tab 2 7.0 Firmware Package.
- Odin Flasher ( P3100 ).
- USB Drivers.

- After your download the wanted tools you have to extract them and install the USB drivers and then reboot your PC.

Firmware Update Steps:

- Run Odin Flasher and Check these: Re-Partition, Auto Reboot, F.Reset Time.

- Now you have to select the suitable PIT file according to your tablet type:

signed_espresso_20120220_16G.pit

Or

signed_espresso_20120220_8G.pit

- Now from the Extracted Firmware Package you have to select the Files like this:

BOOTLOADER: BOOTLOADER_P3100xxxxx_372946_REV04_user_low_ship.tar.md5

PDA: PLATFORM_P3100xxxxx_372946_REV04_user_low_ship.tar.md5

PHONE: MODEM_P3100xxxx_REV_04_CL1128355.tar.md5

CSC: CSC_Oxx_P3100Oxxxxx_396275_REV04_user_low_ship.tar.md5

- Put the Tablet into Download Mode: Press Volume Down key + Power for 10 sec then press Volume Up key to enter Download Mode.

- Connect the Tablet to your PC by USB cable and install needed drivers.

- When the Tablet detected by Odin that mean all drivers is installed correctly.

- Now you can Click Start button and wait till the Tablet rebooted by Odin.

- If you see PASS! word in green on Odin's window that means the process was done with no errors.

- Disconnect your Tablet and Do Full Reset: *2767*3855#.

How To Update Samsung I6210 Firmware

Tools: Samsung I6210 Download Program - USB cable.

Firmware Update Steps:

1. Run Samsung I6210 Download Program.
2. Select MSM6245/MSM6260, and Full Download (check).
3. From the release files, find and select the folder BOOTFILES.
4. Select Modem: amss.bin
5. Select Rsrc1: Rsrc_I6210_xxxx.rc1
6. Select Rsrc2: Rsrc2_I6210_xxxx(low).rc2
7. Select FactoryFS: FactoryFS_I6210_xxxx.ffs
8. Power off the phone, and then press “*” with “END”. You will see the DOWNLOAD screen.
9. Connect the USB cable, and press Port Search. Once you see “Ready…”, press Download
10. After downloading the BOOTFILES, the phone will automatically reboot and continue downloading the remaining files.
11. After downloading, the phone will reboot and auto-rebuild. Once this is done the phone will reboot again.
12. All is Done.

Firmwares: Samsung I6210 Original Firmwares

How To Update Samsung C6712 Star II DUOS Firmware

Firmware Update Guide:

- Run Samsung C6712 Star II Duos Downloader

- Select BRCM2133

- When you need to Update Boot files you have to check Full Download option ( Risky ).

- Click Boot button and select the Boot files folder ( if you checked Full Download )

- Now you have to select Firmwares files in this Guide we select C6712XXKF3 - OXAKF2 as example:

For Apps field: apps_compressed.bin

For Rsrc1 field: Rsrc_C6712_Open_Europe_Common.rc1

For Rsrc2 field: Rsrc2_C6712(Low).rc2

For Factory FS field: FactoryFs_C6712_Open_Europe_Common.ffs

For CSC field: CSC_C6712_Open_Europe_Common_OXAKF2.csc

For SHP APP field: ShpApp.app

- After that you have to put the phone into Download mode: Volume Down + Sim Swap + Power key.

- Connect USB cable to phone and PC and click Port Search to check connection.

- After the program detect the phone you can click Download button to start updating.

- Wait till the phone restart by itself then do full reset: *2767*3855#

Downloads: Samsung C6712 Star II DUOS Original Firmwares.